Integrating Protected HPE Storage Solutions 試験
Question No : 1
A storage integrator has connected a new Windows Server 2012 host to a customer’s fabric where five HPE 3PAR StoreServ arrays are already installed. The integrator plans to create a script to send the information about the new host to all HPE 3PAR arrays in an automated way.
Which Host Explorer command should be used?
Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA4-4524ENW.pdf (12)
Question No : 2
You are installing an additional HPE 3PAR StoreServ SFF disk enclosure in an HPE 3PAR 8200 StoreServ array. The newly-installed enclosure appears as cage1.
You are able to verify from the 3PAR CLI that both cage0 and cage1 appear.
However, you notice an error in the system health:
Click on the controller enclosure port you would look at to start troubleshooting this issue.
Question No : 3
What must be configured before a storage integrator can start creating volumes from the available space on an HPE MSA 1040/2040?
Question No : 4
A storage integrator is planning an HPE StoreVirtual VSA installation.
Which network-related information may be needed for the implementation?
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c05049837 (4)
Question No : 5
A storage integrator wants to change the tiering affinity of an existing volume on an HPE MSA 1040/2040 with GL220 and higher.
How can this goal be achieved?
Reference: https://h20195.www2.hpe.com/v2/GetPDF.aspx/4AA4-6892ENW.pdf (24)
Question No : 6
Refer to the exhibit.
Which port can be used to connect the HPE MSA 2040 controller to hosts?
Reference: https://support.hpe.com/hpsc/doc/public/display?docId=c03792322 (10)
Question No : 7
Your customer has a requirement to provide identification information to the PDU such as server name, UUID number, and IP address from their ProLiant-based storage products.
Which PDU do you recommend to meet this requirement?
Question No : 8
A storage integrator installed an HPE 3PAR StoreServ system.
For which default accounts will the storage integrator need to hand over changed passwords to the customer?
Question No : 9
A system engineer installed HPE Insight Remote Support for an HPE MSA 2042 storage system at a customer’s site. The engineer wants to integrate the system in HPE Insight Online to monitor it remotely.
Which information does the engineer need from the customer to do the integration, using the Insight Remote Support GUI with HPE Insight Online? (Choose two.)
Question No : 10
Refer to the exhibit.
A storage integrator is examining the configuration of an HPE 3PAR storage system using CLI.
Which command can be used to display a list of common provisioning groups starting with substring R5 in the system?
Question No : 11
A storage integrator is validating an HPE 3PAR StoreServ implementation. The integrator created a volume in the HPE 3PAR StoreServ Management Console (SSMC) and needs to verify read/write access from a Linux operating system.
Which steps are part of the verification process? (Choose two.)
Question No : 12
Click on an available port that can be used to connect an HPE 3PAR StoreServ 8000 to drive enclosures. (Click on the correct port.)
Question No : 13
A customer has HPE Data Protector and a StoreOnce VSA at a remote site that must replicate to the corporate data center StoreOnce backup device.
What considerations must be taken into account to allow for Catalyst replication?
A. Data Protector Catalyst replication will rehydrate the data on the StoreOnce VSA then write to the data center StoreOnce.
B. Data Protector will write 2 backups: one to the StoreOnce VSA, the other to StoreOnce at the data center.
C. Data Protector Catalyst replication requires gateways to both sites to use Object copy.
D. Data Protector Catalyst replication is configured through the replication license on the StoreOnce VSA.
Question No : 14
When using the CLI for performance monitoring on an HPE 3PAR array, for which component in the datapath would the “stavlun” command give an output? (Click on the correct option.)
Question No : 15
A customer with an HPE 3PAR 8200 unit has concerns about tracking missing updates and where to find the information on when upgrades were done in the past. With previous storage systems the customer ran out of storage before knowing that they needed to order more storage.
What can the integrator do to help the customer with these concerns?